Super BMW ICOM PRO N3+ Full Configuration Supports DoIP J2534 Compatible with BMW ICOM V2024.03 Software
The
Super BMW ICOM Pro N3+ is developed on the basis of BMW's special
inspection devices ICOM A1, A2, A3, and N3. On the basis of inheriting
the advantages of these products, N3+ optimizes and upgrades them. It is
100% compatible with the original BM-W special inspection software
without any software changes, and J2534 and DOIP are added on the basis
of the special inspection.
The N3+ is the same as the N3, with
one code for one machine, and the wireless is bonded with the machine
code, which is convenient for customer service and product tracking.
Notion!!!!
To use N3+ as Benz DoIP device, you need to have Benz license activated.
Devices purchased before Oct. 1st, 2023 will receive Benz license activation for free.
Super ICOM PRO N3+ Highlights:
Supports WiFi and USB connection.
Firmware update online
Replace ICOM Next and ENET cable. Fully compatible BMW ICOM ISTA-D, ISTA-P, INPA, WinKFP, E-sys etc engineering software
With OBDII to 20-PIN cable for old BM-W and 10-PIN cable for BM-W motorcycle
Compatible with DoIP protocol
Can be used as J2534 Passthru device for ODIS HDS TIS GDS2 SDD etc
Product Description
1. Supports Original BMW ICOM Software.
2. Firmware update via original ICOM firmware file.
3. SUPER ICOM PRO N3+ = BMW ICOM software + J2534 + DOIP + WIFI device
4. Super ICOM PRO N3+ BMW Diagnostic Tool Supports DoIP J2534
Product Features:
Synchronized Upgrade with the Original Factory
The firmware of the N3+ product has been refreshed to version 149 when
it leaves the factory. The firmware upgrade is synchronized with the
original factory and the steps are the same. If there is an update to
the firmware in the future, customers can download it from the official
website of the original factory and then upgrade.
Wired + Wireless Mode
The communication interface between the N3+ and the computer adopts wired + wireless mode.
Wired mode: Wired adopts standard USB3.0 interface. Compared with the
old RJ45 network port of the original factory, we have better
compatibility and stronger applicability for existing general-purpose
computers and tablets. (The first time you need to set the dedicated IP
address)
Wireless mode: The latest low-power consumption design is
used for wireless mode, which reduces the heat of the product in use and
greatly improves the speed and stability of wireless communication.
After one wireless connection, it can be automatically connected after
booting. (Wireless needs to be wired disconnected.)
Dual Heat Dissipation Design
The N3+ product adopts a dual heat dissipation design of a fan and a
heat sink, which has not yet appeared on the market in the BMW special
inspection and greatly improves the durability and stability of the
product's communication in high-temperature environments.
Optimized Main Cable
Because the communication protocol of N3+ includes K line, CAN line and
local area network (DOIP) communication, in order to ensure the
stability of communication, we have optimized and improved the main
cable for testing, which is not an ordinary OBD cable.
On the basis
of N3, the N3+ adds a one-key switch button, which can be freely
switched between the special inspection and J2534 software by pressing
and holding it for 3 seconds.
Firmware Update Online:
The Super ICOM Pro N3+ adopts the original ICOM solution. The firmware
upgrade is synchronized with the original factory and the steps are the
same. If there is an update to the firmware in the future, users can
download it from the official website of the original factory and then
upgrade. Current firmware version goes to V149.
How to update Super ICOM Pro N3+ firmware? (Pls contact our customer service to get latest update instruction)
Super ICOM Pro N3 Plus Functions:
1. BMW ICOM device (NEXT A3)
N3+ adopts the same technology as BMW's special tester, and its
comprehensive performance is much higher than similar products. All
BMW's test software can run 100% without any problems, and all test
results are 100% consistent with the original factory. The test scope
includes BMW cars, motorcycles, Rolls Royce and so on.
2. J2534 device
N3+ can use the J2534 protocol to read through after switching with one
key. It is compatible with the 6-pin and 14-pin CAN communication and
the 7-pin K-line communication of the OBD port. It can use Volkswagen,
Mercedes-Benz, Toyota, Honda, Land Rover and other special inspection
software with J2534 interface.
3. DOIP device
N3+ can use DOIP network communication protocol after one-key
switching, which can solve the problem that Volkswagen 5054 and
Mercedes-Benz C4 cannot test new cars without DOIP.
4. WIFI device
When N3+ uses the BMW special inspection software, it is more
convenient and faster to use WIFI, without any configuration on the
computer. After one-key switching, WIFI can use BMW's mobile phone
hidden functions activation and test software, which can be used to test
the DOIP of Mercedes-Benz Volkswagen before 2023.
How to set up Super ICOM N3 as J2534 or DoIP device? (Pls contact our customer service）
Option 1:
Package Includes:
1pc x SUPER ICOM PRO N3+ main host
1pc x OBD cable
1pc x USB cable（2 meters long）
1pc x 20-pin round head cable
1pc x 10-pin motorcycle cable
Option 2:
Package Includes:
1pc x SUPER ICOM PRO N3+ main host
1pc x OBD cable
1pc x USB cable（2 meters long）
1pc x 20-pin round head cable
1pc x 10-pin motorcycle cable
1pc x V2024.03 BMW ICOM Software 1TB SSD
Option 3:
Package Includes:
1pc x SUPER ICOM PRO N3+ main host
1pc x OBD cable
1pc x USB cable（2 meters long）
1pc x 20-pin round head cable
1pc x 10-pin motorcycle cable
1pc x Second Hand Lenovo T450 Laptop with BMW ICOM V2024.03 software
Second Hand Laptop Lenovo T450
Specification:
Brand: Lenovo
Condition: Used
Type:Laptop/Notebook
Screen Size:12.5
Processor Type:Intel (R) Core(TM) I5-5200U CPU
Memory: 8GB
V2024.03 Newest Vsrsion Software ISTA-D ISTA 4.46.14 ISTA-P 3.71.0.200 with Engineer Programming
Software Version : V2024.03
ISTA - D: 4.46.14 with SDP Programming Database 4.46.11
ISTA - P: 3.71.0.200 with Engineer Programming，supports the programming of BMW motorcycles and electric vehicles can program F/G/I/K chassis for car (through the ICOM, not other cable )
Vin: V2024.03
BMW ETK: 2020.01
BMW KSD: 2019.12 Multilanguage
BMW FSC Navigation Code Generator
BMWAiCoder for BMW Coding
Win10 64 bit operating system
BMW ICOM V2024.03, With free Software:
1. Get engineer version, INPA 5.06,winkfp 5.3.1,NCS 3.5.1, E-sys PLUS 3.81,e-sys 3.35.3,data V71.0
2. get Chinese software DR.GINI B022
3. get count code navigation tool software FSC operator code
4. get one-clik hidden brush tool BMWAi V4.6
5. Add DIS Software for Old cars, DISV57 and DISV44,diagnosis and programming for BMW virtual machines
6. Support Vehicles: For BMW Cars,For BMW Motorcycle,For Rolls-Royce, For Mini Cooper
Notice : The software installed English language in default.
ISTA-D Language: Czech, Dutch, French, German, Greek, Italian, Japanese, Korean, Polish, Portuguese, Russian, Spanish, Sweden, Thai, Turkish
ISTA-P Language: English, Chinese, Czech, Dutch, French, German, Greek, Indonesian, Italian, Japanese, Korean, Polish,
Portuguese, Russian, Spanish, Swedish, Thai, Turkish
